4th Generation
Thread forming Tapping Screw for thermoplastic!!
Self-Tapping Screws for Plastic "Non-Sert" Products
Nonsert Steel 3Cr. Plating thickness 5μm guarantee.
Please do not hesitate to contact us
No Need Metal Insert
Possible to reduce the cost without metal insert.
No need countersinking process & expense for the metal insert.
non-sert will help you save total cost and time
Sharp thread angle “30°”
Less stress and cracking on your plastic product.
Best for repeat use
Trilobular thread = Low driving torque = less stress on the plastic.
non-sert can be used repeatedly on the same pilot hole
Low driving torque[TD] & High failure torque[TF]
Ttrilobular thread & sharp thread angle "30°" achieve low TD & high TF.
Pilot hole dia. & Torque of setting
Torque Analyzer will...
- Find the best hole dia
- Find the best setting torque
Please feel to ask us if you're annoyed with cracking & idling
"Non-Sert" Hole size (Self-Tapping Screws for Plastic)
Non-Sert is thread forming tapping screw to plastic material directly.
This thread structure is difficult to idling, and repeatable use
※This table is as only reference.
Material | hole size (d Size x) | |
---|---|---|
ABS | 0.80 | |
PA6/6.6 | 0.75 | |
PC | 0.85 | |
PE | 0.70 - 0.75 | |
PET | 0.75 | |
PMMA | 0.85 | |
POM | 0.75 | |
PP | 0.70 | |
PPO | 0.80 | |
PS | 0.80 | |
FRP | PET 30% | 0.80 |
PA6 30% | 0.82 | |
PA6.6 30% | 0.85 | |
PC 30% | 0.80 |
※The best condition of hole diameter varies depending on the material and shape, so We recommend using a PC torque analyzer to measure the optimum hole diameter.
NonSert Application Situation
- No Metal Insert Required. Cost Reduction.
- Easy to recycle without metal insert.
- Cracking is not expected
- Plastic Crack happen place
- Repeatable application
- Low torque driving, low stress for Self Tapping Screws Plastic
Applications

HOCHIKI Corporation
Gas alarmBy adopting nonsert, it can be used as it is for plastic and it becomes possible to use it repeatedly for maintenance
Microphone Capsule
M1.6x4.0 Nonsert tighten strictly for microphone parts.Welco Corporation
High performance small tube pumpAdopted nonsert for fastening of motor part and tube part housing
Plasma TV stand
By adopting nonsert, costs are reduced without requiring inserts
Trolley for pachinko parlor
Even with heavy pachinko balls it is hard to loosen
Nonsert is also strong for loose
SY-Non-Sert for SANYO DENKI FAN '' SAN ACE ''
This is special Non-Sert with development together.
"120° Flat Head type and Small Pan Head type Nonsert"
These SY-Non-Serts are is recommended
by the SANYO DENKI CO., Ltd Technical date as below.
4thGeneration Thread Forming
plastic, Plastic and Engineering Plastic Fastening Plastic counterpart is much weaker than Steel Screw.
Therefore, to prevent the plastic breaking or cracking, SAIMA is stronly recommended to use “specialized screw for plastic”.
1st Generation: JIS B 1122 type 2 (Self Tapping Screws for Plastic)
Suitable for thin plate and plastic fastening as stated in JIS B1122 appendix.
Widely distributed as a standard screw. Average Performance.
2nd Generation: B-type (Self Tapping Screws for Plastic)
Advanced form of JIS B 1122 Class 2, with trilobular thread, same thread angle (60 degree) and pitch.
Tightening Torque is lower than 1st generation according to torque analysis result.
Suitable for thin plate and plastic fastening.
3rd Generation : P-type (Self Tapping Screws for Plastic)
Double threaded with 45° thread angle, wider thread compared with B-type and trilobular thread.
Double started thread makes the fastening speed twice high, but loosens faster once the screw starts loosening.
This makes TF point and TD point higher, so we havet to pay attention F/D ratio.
This is not suitable for repeated application on the same pilot hole.
TD: Torque of Driving
Min. Torque for fatening
TF: Torque of Failure
Torque for breaking counter material. it includes idling and crack
TS: Torque of Setting
Best Torque of Setting
4th Generation : Non-Sert (Self Tapping Screws for Plastic)
Single threaded same as 1st and 2nd Generation with 30 degree thread angle, trilobular thread shape and large pitch. Lowest TD(Torque of Driving) in all generations. Low stress against the plastic part. TF(Torque of Failure) is lower than 3rd Generation, but mostly T/F ratio indicate higher, these results conclude that using Non-Sert is safe and best Self Tapping Screws for Self Tapping Screws for Plastic fastening. In addition that Best for repeat use on the same hole.
Catalog of Self Tapping Screw "Non-Sert"